由于这些变化，在联机模式期间
不会显示在屏幕上！
如果参数（或参数位）连接到
一个块，你点击这个输入引脚（或任何输出引脚），而
按住Shift键，此参数的实际值（或
输出引脚）以数字形式实时显示在屏幕上。
注意：如果您有DriveWindow并且启用了
同时使用DriveWindow和DriveAP，您可以监视
使用DriveWindow以图形方式显示参数值，同时使用DriveAP
跑步
再次单击（按住）可以删除值显示
按下Shift键）。
标准用户界面：AP程序的状态（正在运行，
屏幕上会显示已连接驱动器中的（已停止或编辑）
可以通过菜单命令Drive-Start、Drive-Stop进行更改
和驱动-编辑。
用户界面：当前可见时间级别的状态
连接驱动器中的（运行、停止或编辑）显示在
屏幕，可以通过菜单命令“驱动-启动”进行更改
时间级别，驱动-停止此时间级别并驱动-编辑此
时间级别。
可以通过菜单命令更改所有时间级别的状态
驱动-启动所有时间级别，驱动-停止所有时间级别和
驱动-编辑所有时间级别。
连接驱动器的状态信息显示在
在驱动器状态框中实时显示。参考值
按住Shift键的同时单击屏幕，可以将其删除
钥匙
标准用户界面：所有非AP参数的列表为
显示在功能块下方的列表框中。
用户界面：参数窗口列出所有非AP
参数。如果删除此窗口，您可以通过
按F2键（或通过菜单命令驱动-参数列表-
显示参数列表）。
可以读取参数列表中所有参数的当前值
从“驱动方式”菜单命令“驱动-参数列表-上载”
值（参数的当前值可以通过单个
单击列表中的此参数）。
您可以更改驱动方式中非AP参数的值
双击列表中所需的参数。
DriveAP的使用
3-6 DriveAP用户手册
联机模式由菜单命令Drive-Off Line停止。这个
DriveAP的操作模式现在将恢复为离线模式。
屏幕上的程序修改不再复制到
连接的驱动器和块引脚的实时监控（如果定义
由用户）从屏幕上删除。
您可以通过菜单命令在屏幕上显示AP程序
文件-新建、文件-打开或驱动器-上载。
现在，您可以通过单击屏幕上的
按住Alt键或Ctrl键时所需的程序项
钥匙
通过鼠标右键，可以快速显示上下文相关信息
帮助这说明了在
光标（如有）。
如果鼠标右键时光标位于块的销上
按钮，快速帮助列出可用的pin操作。
如果光标位于块上并按F3键，则
此块显示在信息窗口中。
用户界面：如果输入pin连接到用户
常数，您可以通过单击更改此用户常数的值
按住Shift键的同时在输入引脚上。
注：如果DriveAP的工作模式为联机模式，则所有
对屏幕上程序的修改会自动复制
连接到连接驱动器中的程序。
•如果您先单击块的输出引脚，然后单击输入
块的引脚，该输入引脚连接到输出引脚。
•如果您首先单击用户常数（在左侧的高部分
然后在块的输入引脚上，该输入引脚是
连接到用户常数。
•如果先单击块的输出引脚，然后单击指针
参数（在右侧），此指针参数已连接
至输出引脚。
•如果您想将块移动到另一个位置（在本页或
另一个页面），首先单击所需的块，然后单击
所需页面上的所需空网格交叉点（必须有
这一点周围有足够的空白）。
程序
修改
用鼠标单击
Alt键
（标准用户
接口）
用鼠标单击
Alt键
（用户
接口）

some other means) during the On-Line Mode since these changes are not displayed on the screen! If a parameter (or a bit of a parameter) is
connected to an input pin of a block and you click on this input pin (or on any output pin) while holding down the Shift key, the actual value of this parameter (or this output pin) is displayed numerically on the screen in real time. Note: If you have DriveWindow and you have enabled the simultaneous use of DriveWindow with DriveAP, you can monitor parameter values graphically with DriveWindow while DriveAP is running. The value display can be removed by clicking again (while holding down the Shift key) on the same pin. Standard User Interface: The state of the AP program (Running, Stopped or Edit) in the connected drive is displayed on the screen and can be changed by menu commands Drive - Start, Drive - Stop and Drive - Edit. Advanced User Interface: The state of the currently visible time level (Running, Stopped or Edit) in the connected drive is displayed on the screen and can be changed by menu commands Drive - Start This Time Level, Drive - Stop This Time Level and Drive - Edit This Time Level. The states of all time levels can be changed by menu commands Drive - Start All Time Levels, Drive - Stop All Time Levels and Drive - Edit All Time Levels. The status information of the connected drive is displayed on the screen in real time in the DRIVE STATUS box. The reference value display can be removed by clicking on it while holding down the Shift key. Standard User Interface: The list of all non-AP parameters is displayed in the list box below the function blocks. Advanced User Interface: The Parameter Window lists all non-AP parameters. If you remove this window, you can see it again by pressing the F2 key (or by menu command Drive - Parameter List - Display Parameter List). Current values of all parameters in the parameter list can be read from the drive by menu command Drive - Parameter List - Upload Values (the current value of a parameter can be read by single clicking on this parameter in the list). You can change the value of a non-AP parameter in the drive by double clicking on the desired parameter in the list. Use of DriveAP 3-6 DriveAP User’s Manual On-Line Mode is stopped by menu command Drive - Off-Line. The operating mode of DriveAP will now revert to the Off-Line Mode. Program modifications on the screen are no more copied to the connected drive and the real time monitoring of block pins (if defined by the user) is removed from the screen. You can display an AP program on the screen by menu command File - New, File - Open or Drive - Upload. Now you can modify the program on the screen by clicking on the desired program item while holding down either the Alt key or the Ctrl key. By the right button of the mouse you display context-sensitive Quick Help. This tells the actions that are possible with the item under the cursor (if any). If the cursor is e.g. on a pin of a block when you press mouse’s right button, Quick Help lists the available pin actions. If the cursor is on a block and you press the F3 key, the description of this block is displayed in the Info window. Advanced User Interface: If an input pin is connected to an User Constant, you can change the value of this User Constant by clicking on the input pin while holding down the Shift key. Note: If the operating mode of DriveAP is On-Line Mode, all modifications to the program on the screen are automatically copied to the program in the connected drive. • If you click first on an output pin of a block and then on an input pin of a block, this input pin is connected to the output pin. • If you click first on an user constant (in the highest part of the left side) and then on an input pin of a block, this input pin is connected to the user constant. • If you click first on an output pin of a block and then on a Pointer Parameter (at the right side), this Pointer Parameter is connected to the output pin. • If you want to move a block to another location (on this page or on another page), you first click on the desired block and then on the desired empty grid crossing point on the desired page (there must be enough empty space around this point). Program Modification Mouse Click with the Alt Key (Standard User Interface) Mouse Click with the Alt Key (Advanced User Interface)