PE110NSFPPE110
处理器PowerPC 266 MHz RAM 32 MB SDRAM程序存储器128 KB NVRAM（剩余）编程模块32 MB紧凑型闪存卡状态显示4位数字，字母数字接口PROG：1×RS232、RS422和RS485，无控制信号，隔离COM：1×RS232、RS422和RS485（带控制信号的RS232），无隔离sercos：2/4/8/16 MBaud可选接口Profibus从模块（P2），Interbus从模块（B2）、DeviceNet从模块（V2）、Arcnet从模块、交叉通信（Q1）、Profibus主模块（P1）、DeviceNet主模块（V1）、凸轮轴齿轮主模块（N1）、凸轮轴齿轮从模块（N2）以太网：10/100BaseT（RJ45）端，1 VPP-2×（G2）2×交叉通信，Arcnet（Q2）电源DC 24 V（标称值）电压波动，大5%范围：19.2 V-30 V（包括纹波系数）BB继电器输入电压24 V（标称值）输入电流，大150 mA常开（NO）触点，小开关周期为500 000次（过电流电压保护）DOK-CONTRL-PPC-R22.1**-IT01-EN-P力士乐IndraControl PPC-R22.1控制博世力士乐股份公司技术数据11/33直流24 V时的大功耗1.2 A（+2.2 A大电源输入/输出总线）保护引线大4 A 24 V延时保险丝大4 A 24 Ve电缆横截面的延时保险丝电源线0.75至1.5 mm2（取决于电源需求）防护等级IP 20重量1.3 kg实时时钟缓冲时间TA 45°C下5天图7-1：技术控制数据模块大24 V电源2.2 A模块大5 V电源2.6 A总功率大52 W降额：0-35°C→ 100%（52 W）35-45℃→ 85%（44 W）图7-2：控制3数字24 V输入（无电势）“0”信号的输入/输出总线电源：输入电压–3 V至5 V输入电压≤ 2.5 mA“1”信号：输入电压11 V至30 V输入电压2.8 mA≤ 我≤ 6 mA延迟时间：通常为100µs 2数字24 V输出（无电势）输出电压24 V输出电压0.5 A（标称值）防短路“1”信号：2 mA至0.6 A电压降≤ 1.5 V“0”信号：泄漏电流≤ 0.5 mA延迟时间：≤ 500µs

Processor PowerPC 266 MHz RAM 32 MB SDRAM Program memory 128 KB NVRAM (remanent) Programming module 32 MB Compact Flash card Status display 4-digit, alphanumerical Interfaces PROG: 1 × RS232, RS422 and RS485 without control signals, isolated COM: 1 × RS232, RS422 and RS485 (RS232 with control signals), without isolation sercos: 2/4/8/16 MBaud Optional interfaces Profibus slave module (P2), Interbus slave module (B2), DeviceNet slave module (V2), Arcnet slave module, cross communica‐ tion (Q1), Profibus master module (P1), DeviceNet master module (V1), Camshaft gear master module (N1), Camshaft gear slave module (N2) Ethernet: 10/100BaseT (RJ45) EnDat, 1 VPP - 2 × (G2) 2 × cross communication, Arcnet (Q2) Voltage supply DC 24 V (nominal value) Voltage ripple, max. 5 % Range: 19.2 V - 30 V (ripple factor inclu‐ ded) BB relay Input voltage 24 V (nominal value) Input current, max. 150 mA Normally open (NO) contact with min. 500 000 switching cycles (overcurrent voltageprotected) DOK-CONTRL-PPC-R22.1**-IT01-EN-P Rexroth IndraControl PPC-R22.1 Control Bosch Rexroth AG Technical Data 11/33 Maximum power consumption at DC 24 V 1.2 A (+2.2 A maximum supply I/O bus) Protecting the leads max. 4 A time lag fuse for 24 V max. 4 A time lag fuse for 24 Ve Cable cross section of the supply lines 0.75 to 1.5 mm2 (depending on the power demand) Degree of protection IP 20 Weight 1.3 kg Real-time clock Buffer time 5 days at TA 45 °C Fig.7-1: Technical control data Module supply 24 V Maximum 2.2 A Module supply 5 V Maximum 2.6 A Total power Maximum 52 W Derating: 0 - 35 °C → 100 % (52 W) 35 - 45 ℃ → 85 % (44 W) Fig.7-2: I/O bus supply by control 3 digital 24 V inputs (potential-free) "0" signal: Input voltage –3 V to 5 V Input voltage ≤ 2.5 mA "1" signal: Input voltage 11 V to 30 V Input voltage 2.8 mA ≤ I ≤ 6 mA Delay time: Typically 100 µs 2 digital 24 V outputs (potential-free) Output voltage 24 V Output voltage 0.5 A (nominal value) Short-circuit proof "1" signal: 2 mA up to 0.6 A Voltage dip ≤ 1.5 V "0" signal: Leakage current ≤ 0.5 mA Delay time: ≤ 500 µs