MAC112D-0-ED-4-​C/130-B-2/WI522​LV/S018
对于每个相应的电机系列，抱闸具有以下抱闸扭矩。图2.12：抱闸电源连接的保持扭矩用户必须根据机器的条件命令电源连接的输出方向。出厂后不能改变输出方向。以下型号可用（另请参见图2.13）：•A侧连接器•B侧连接器•右侧连接器•左侧连接器注意：对于MAC 063s，只有朝向A侧或B侧的输出方向可用。图2.13：电源连接的可能输出方向如果电机存放时间超过两年，则有必要在使用前磨合。研磨：1。以大约100速的速度运行电机。2、关闭抱闸并保持其关闭约60秒。注意：打开制动保持器至PLC或硬件电路的导线。3、60秒后关闭驱动器。4、将抱闸重新连接至PLC或硬件电路。保持扭矩MAC…063 071 090 093 112 115 3 Nm X 6.5 Nm X X 14 Nm X 22 Nm X 40 Nm X 1）45 Nm X 60 Nm X 1）X 1）不适用于电机长度A。右左侧A侧B侧FAABGANG 2。技术数据•DOK-MOTOR*-MAC******-PRJ1-EN-P•04.96 21反馈连接器根据安装条件，可以选择不同类型的连接器连接电机反馈电缆。可用的有：•直接头和•角接头。可在尺寸数据表和13.2节“反馈连接器”中找到关于连接器类型到电机类型分配的信息。直线连接器图2.14描述了一个带有转速表反馈和直线编码器连接器的电机。图2.14：带有直转速表反馈和编码器连接器角连接器INDRAMAT的MAC电机提供并交付角连接器，以便电缆插入法兰插座后的输出方向为电机的B侧。图2.15：带角连接器的MAC电机（B侧为交付时的输出方向），用户可以更改输出方向。只需松开四个固定螺钉（见图2.16）。现在可以将接头零件以90°的增量转动到所需的位置。重新拧紧螺钉时，确保垫圈和电缆芯线均未损坏。

The holding brake is available with the following holding torques for each respective motor series. Fig 2.12: The holding torque of the holding brakes Power connection The user must order the output direction of the power connections in accordance with the conditions at the machine. The output direction cannot be altered after delivery. The following variants are available (also see Figure 2.13): • connector to side A • connector to side B • connector to the right • connector to the left Note: With the MAC 063s only the output directions towards side A or side B are available. Fig 2.13: Possible output directions of the power connections If the motor is stored for a period exceeding two years, then it is necessary to grind it in before using it. To grind it in: 1. Run the motor at a speed of approximately 100 speed. 2. Close the holding brake and keep it closed for approximately 60 seconds. Note: Open the conductor of the holding brake to the PLC or the hardware circuitry. 3. Shut down the drive after 60 seconds. 4. Reconnect the holding brake to the PLC or the hardware circuitry. Holding torque MAC … 063 071 090 093 112 115 3 Nm X X 6.5 Nm X X X 14 Nm X X X 22 Nm X 40 Nm X 1) 45 Nm X 60 Nm X 1) X 1)Not available for motor length A. RIGHT LEFT SIDE A SIDE B FAABGANG 2. Technical Data • DOK-MOTOR*-MAC********-PRJ1-EN-P • 04.96 21 Feedback connector Different types of connectors can be selected for connecting the motor feedback cable depending upon the installation conditions. Available are: • straight connectors and • angle connectors. Information about the allocation of connector type to motor type can be found in the dimensional data sheets and in section 13.2 "Connector for the Feedback". Straight connector Figure 2.14 depicts a motor with tachofeedback and straight encoder connector. Fig 2.14: A MAC motor with straight tachofeedback and encoder connectors Angle connector INDRAMAT supplies and delivers the angle connectors so that the output direction of the cable, once inserted into the flanged socket, is side B of the motor. Fig 2.15: A MAC motor with angle connector (side B is output direction at delivery) The user can change the output direction. Just release the four fixing screws (see Figure 2.16). The connector parts can now be turned in increments of 90° into the position desired. Make sure that neither the gasket nor the cable cores of the cable are damaged when re-tightening the screws.