MAC112D-0-ED-4-​C/130-A-0/WI520​LX/S005
导向器直径为了与其他制造商的电机兼容，除了标准类型外，还可以选择具有自定义导向器直径的安装法兰。这仅适用于部分电机。这个
图2.8中的表格列出了选择和适当的尺寸。
图2.7：定义术语定心/导向直径
图2.8：单个电机系列的导向器直径
输出轴用户可以选择输出轴的设计。因达拉马特
建议使用普通输出轴。
普通输出轴
可以实现无齿隙和非正扭矩传输
带普通轴。夹紧装置、压力套筒或类似夹紧部件可用于连接小齿轮、皮带轮或类似元件。
带键槽的输出轴
带键槽的输出轴符合DIN中规定的要求
6885，1页，8/68版。这实现了形状匹配扭矩传输。
这种类型的轴毂连接适合较小的需求。在电机安装方向为IM V3的情况下，采用多轴电机
和IM V19，有必要防止液体在
输出轴超过较长时间。即使使用轴
密封并不能防止液体沿着
将输出轴插入电机壳体中。
电动机系列
导向器直径（mm）
标准类型自定义类型
MAC 063 95-
MAC 071 95-
MAC 090 110 130
MAC 093 110 130
MAC 112 130 180
MAC 115 130 180
输出轴，输出轴
安装法兰
法森特里尔
对中
直径
2、技术资料
•DOK-电机*-MAC******-PRJ1-EN-P•04.96 17
由于扭转，轴毂连接处出现轴向应力状态，
弯曲、径向和轴向载荷。在强大的反向操作过程中，键的底部可能会翻转并降低同心度的质量。不断增加的变形可能导致断裂。平原的使用
因此，建议使用摩擦锁定连接的轴端。

Pilot diameter To generate compatibility with the motors of other manufacturers, it is possible to also select a mounting flange with a customized pilot diameter in addition to the standard types. This is possible only with some of the motors. The choices and appropriate dimensions are listed in the table in Figure 2.8. Fig 2.7: Defining the term centering / pilot diameter Fig 2.8: Pilot diameters for the individual motor series Output shaft The design of the output shaft can be selected by the user. INDRAMAT recommends the use of plain output shafts. Plain output shaft A backlash-free and non-positive transmission of torque can be achieved with a plain shaft. Clamping sets, pressure sleeves or similar clamping components can be used for coupling pinions, belt pulleys or similar elements. Output shaft with keyway The output shaft with keyway adheres to the requirements specified in DIN 6885, sheet 1, 8/68 edition. This achieves a form-fitting torque transmission. This type of shaft-hub connection is suitable for lesser demands. A multiIn those cases where the motors are mounted in orientations IM V3 and IM V19, it is necessary to prevent liquids from collecting at the output shaft over extended periods of time. Even the use of a shaft sealing does not absolutely prevent liquids from penetrating, along the output shaft, into the housing of the motor. Motor Series Pilot diameter in mm Standard types Customized types MAC 063 95 — MAC 071 95 — MAC 090 110 130 MAC 093 110 130 MAC 112 130 180 MAC 115 130 180 output shaft mounting flange FAZENTRIERD centering diameter 2. Technical Data • DOK-MOTOR*-MAC********-PRJ1-EN-P • 04.96 17 axial stress state occurs at the shaft-hub connection as a result of torsion, bending, radial and axial loads. It is possible, during powerful reverse operations, for the bottom of the key to turn out and reduce the quality of concentricity. Ever-increasing deformations can cause fractures. The use of plain shaft ends with friction-locked connections is therefore recommended.