VDIPF0302
参数名称功能范围/选项Pswrd配置参数菜单访问密码范围为：0到1000 DI 1定义二进制输入的使用DI1无，Rem NSB，RemOVR，Filter，Service，Fan lock DI 2定义二进制输入的使用DI2无，Rem NSB，RemOVR，Filter，Service，Fan lock lock设置键盘锁定级别0，1，2 pwr del将恒温器的通电延迟设置为10至120秒Frost pr启用防冻保护打开或关闭heat max将大加热设定点限制设置为40至90°F（4.5至32.0°C）cool min将小冷却设定点限制设置为54至100°F（12.0至37.5°C）PB并将比例带设置为2至8°F（0.6至3.9°C）反循环设置小开/关操作时间阶段0、1、2、3、4、5分钟加热cph设置每小时加热阶段的大循环次数3、4、5、6、7、8冷却cph设置每小时冷却阶段的大循环次数3、4死区设置冷却和加热设定点2、3、，4°F（1.0至2.0°C）fan cont将风扇控制模式设置为加热模式ON或OFF fan del在请求结束后打开或关闭Com Addr*将节温器的Com地址设置为0至254 PAN ID**将节温器的PAN ID设置为0至500通道**将节温器的通道设置为10至26 Get From**选择节温器将配置从0导入到254 TOCTIME设置覆盖0到12小时时的临时占用时间校准RS室温传感器校准±5.0°F（±2.5°C）校准OS室外气温传感器校准±5.0°F（±2.5°C）HP阶段设置使用的压缩机阶段数1或2小时锁定设置室外气温加热锁定-15到120°F（-26到49°C）C锁定设置室外气温机械冷却锁定-40至95°F（-40至35°C）Unocc TM设置未占用计时器值0.0至24小时（以0.5小时为增量）2/4事件设置占用时间表2或4的事件数辅助控制将辅助触点设置为常开或常开或常闭。Prog rec启用渐进恢复功能打开或关闭高bp设置外部空气温度，辅助热量将在该温度下切断34至90°F（1.0至32.0°C）低bp设置热泵切断时的外部空气温度-40至30°F（-40至-1°C）comf/eco设置热泵与辅助热舒适或经济re阀的运行和交互模式定义热泵换向阀的运行O或B comp/aux设置热泵与辅助加热打开或关闭

Parameter name Function Range/Options Pswrd Configuration parameters menu access password Range is: 0 to 1000 DI 1 Defines the use of binary input DI1 None, Rem NSB, RemOVR, Filter, Service, Fan lock DI 2 Defines the use of binary input DI2 None, Rem NSB, RemOVR, Filter, Service, Fan lock lockout Sets the keypad lockout level 0, 1, 2 pwr del Sets the power-up delay of the thermostat 10 to 120 seconds Frost pr Enables frost protection ON or OFF heat max Sets the maximum heating setpoint limit 40 to 90 °F ( 4.5 to 32.0 °C ) cool min Sets the minimum cooling setpoint limit 54 to 100 °F ( 12.0 to 37.5 °C ) Pband Sets the proportional band setting 2 to 8 °F (0.6 to 3.9 °C ) Anticycle Sets minimum On/Off operation time for stages 0, 1, 2, 3, 4, 5 minutes Heat cph Sets the maximum number of cycles for heating stages per hour 3, 4, 5, 6, 7, 8 cool cph Sets the maximum number of cycles for cooling stages per hour 3, 4 Deadband Sets the minimum deadband between cooling & heating setpoints 2, 3, 4 °F (1.0 to 2.0 °C ) fan cont Sets the fan control mode in heating mode ON or OFF fan del Extends fan operation by 60 seconds after demand ends ON or OFF Com Addr* Sets the Com address of the thermostat 0 to 254 PAN ID** Sets the PAN ID of the thermostat 0 to 500 Channel** Sets the channel of the thermostat 10 to 26 Get From** Chooses thermostat to import configuration from 0 to 254 ToccTime Sets the temporary occupancy time when overriding 0 to 12 hours cal RS Room air temperature sensor calibration ± 5.0 °F ( ± 2.5 °C ) cal OS Outside air temperature sensor calibration ± 5.0 °F ( ± 2.5 °C ) HP stage Sets the number of compressor stages used 1 or 2 H lock Sets the outside air temperature heating lockout -15 to 120 °F ( -26 to 49 °C ) C lock Sets the outside air temperature mechanical cooling lockout -40 to 95 °F ( -40 to 35 °C ) Unocc TM Sets the unoccupied Timer value 0.0 to 24 hours (in 0.5hr increments) 2/4event Sets the number of events for the occupancy schedule 2 or 4 aux cont Sets the auxiliary contact to N.O. or N.C N.O. or N.C Prog rec Enables the progressive recovery function On or Off high bp Sets outside air temperature at which auxiliary heat will be cut off 34 to 90 °F ( 1.0 to 32.0 °C ) low bp Sets outside air temperature at which heat pump will be cut off -40 to 30 °F ( -40 to -1 °C ) comf/eco Sets the operation and interaction mode of the heat pump with the auxiliary heat comfort or economy re valve Defines the heat pump reversing valve operation O or B comp/aux Sets the operation and interaction mode of the heat pump with the auxiliary heat ON or OFF