TSXSCPCX4030
•如果现场收到密封桶中的油，可将其储存在水平位置，如图
3.2并用防水油布覆盖。过滤孔和排气孔应在一个水平位置
线这将避免吸入潮湿空气。如果有任何机油泄漏，很容易识别。
•储存区域应无火灾危险。
e） 配件存放
•应注意以下几点，以保持附件处于良好状态而不受损坏，
锈蚀和灰尘。
•根据装箱单检查并确认收到的所有包装箱均完好无损。
•如果安装工作不可能立即开始，则打开箱子进行检查，
应重新包装，并保留装箱单，以供将来参考和记录。
•所有包装箱应保持在地面上方的适当支架上，以允许空气自由循环
在下面储存区域不应积水。应该有足够的空间
检查、搬运和运输。
•所有易碎物品和仪器应存放在室内。
•所有板条箱应按照制造商在板条箱上提供的标记进行保存。通常情况下，
应保留所有控制箱，如RTCC面板、编组箱、驱动机构等
室内垂直位置。
•板条箱不应相互堆叠。
•严格遵守制造商为特定项目提供的特定存储说明。
•变压器底座下方不应放在地面上，因为这会导致
变压器
图3.2
TBI AF/IMS001/R3变压器安装、调试、运行和维护
37 | P a g e
2.2.12就位
•如果基础已准备就绪，且卸货点/储存地点之间的铁路连接可用，则
变压器主体必须在其自身的滚轮上移动到基础上
变压器终安装完毕。

• If the oil is received at site in sealed drums it may be stored in horizontal position as shown in Fig 3.2 and covered with tarpaulin sheet. Filter holes and air release holes shall be in one horizontal line. This will avoid breathing in of moist air. If there is any leakage of oil it can easily be identified. • The storage area should be free from fire hazards. e) STORAGE OF ACCESSORIES • The following points may be taken care of to keep accessories in good condition without damage, rust and dust. • Check and confirm that all packing cases as per packing list are received in good condition. • If erection work is not likely to commence immediately the boxes, which are opened for inspection, should be repacked and the packing list retained for future reference and records. • All packing cases should be kept above ground on suitable support to allow free circulation of air underneath. Water should not collect in the storage area. There should be sufficient space for inspection, handling and transport. • All fragile items and instruments should be stored indoors. • All crates should be kept as per the markings provided on the crates by manufacturer. As a rule, all control boxes such as RTCC Panel, Marshalling Box, Drive Mechanism etc. should be kept indoors in vertical position. • Crates should not be stacked one over the other. • Strictly adhere to the specific storage instruction provided by the manufacturer for specific items. • Under base of the transformer should not rest on the ground as it will lead to rusting of the transformer. Fig 3.2 TBI AF/IMS001/R3 Installation, Commissioning, Operation & Maintenance of Transformer 37 | P a g e 2.2.12 PLACING IN POSITION • If foundation is ready and if rail link between unloading point/storage place is available, then the main body of the transformer must be moved on its own rollers to the foundation where the transformer is to be erected finally.