TSXPSY5500M
•在3500以下配电变压器上安装冲击检测器（振动检测器）的方法
kVA，并简要介绍了变压器装运期间，如果冲击检测器处于活动状态，应采取的措施
在本节中。
1） 一般信息
•冲击检测器是一种称为（冲击观察2）的装置，如果有，可以显示指示器
运输过程中对变压器的冲击。
2） 利益
•对不当操作起到视觉威慑作用
•通过意识减少错误处理
•提供不当处理的无可争辩的证据
•提醒收件人在验收前检查内容
•促进所有产品处理的责任链
•确认包装的有效性
•帮助识别供应链中的故障点，从生产到运输和存储
•帮助提高产品对接质量
TBI AF/IMS001/R3变压器安装、调试、运行和维护
30 | P a g e
3） 流程图
请遵循以下流程图，说明在现场收到货物后如何采取行动，并基于
电击值班状态：-
TBI AF/IMS001/R3变压器安装、调试、运行和维护
31 | P a g e
2.2.6储存
•在现场收到变压器后，好安装并调试变压器
小延迟。如果不可能，应安装硅胶呼吸器。呼吸器
包含一个油封装置，必须将机油加注到标记的油位才能生效。
•应定期观察硅胶呼吸器，以确保硅胶呈蓝色。凝胶应该
一旦变红，立即更换或脱水。
•建议至少每周一次在储存期间检查硅胶的状况，并将其分解
每月至少一次油电压（BDV），并应保持在50 KV的水平。它是
即使在低电压下也需要保持变压器通电，以便油温约为
比周围环境温度高10°至15°C。

• The method of installation shock detector (vibration detector) on distribution transformer up to 3500 kVA and action to be taken if there is shock detector active during shipment transformer is briefed in this section. 1) GENERAL INFORMATION • Shock Detector is the device which is called (shock watch 2) that can show the indicator if there is shock impact on the transformer during transportation process. 2) BENEFIT • Act as a visual deterrent to improper handling • Reduces mishandling through awareness • Provide indisputable evidence of mishandling • Alert recipient to inspect contents before acceptance • Promotes chain of accountability for all product handling • Confirms effectiveness of packing • Helps identify trouble spot in supply chain, from production to transportation and storage • Help increase quality of product dock to dock TBI AF/IMS001/R3 Installation, Commissioning, Operation & Maintenance of Transformer 30 | P a g e 3) FLOW CHART Please follow below flow chart on how to act after shipment is received at site & based on the status of shock watch: - TBI AF/IMS001/R3 Installation, Commissioning, Operation & Maintenance of Transformer 31 | P a g e 2.2.6 STORAGE • On receipt of the Transformer at site, it is desirable to install and commission the transformers with minimum delay. In case, this is not possible, the silica-gel breather should be fitted. The breather incorporates an oil sealing device which must be filled with oil to the marked level to be effective. • A periodic watch should be kept on the silica-gel breather to ensure that the gel is blue. The gel should be replaced or dehydrated immediately on it turning pink. • It is advisable to check the condition of silica gel during storage at least once a week and Break down Voltage (BDV) of oil at least once in a month and should be maintained at a level of 50 KV. It is desirable to keep the transformer energised even at a low voltage so that the oil temperature is about 10° to 15° C higher than the surrounding ambient temperature.