AS-BDAP-210
使用显示器配置设置参数您可以使用显示器配置参数的子集。1、导航至Maint>Setup。2、输入设置密码（默认为“0”），然后按OK。3、导航至Meter>Advan。4、移动光标指向要修改的参数，然后按编辑。5、根据需要修改参数，然后按OK。6、移动光标指向要修改的下一个参数，按Edit，进行更改，然后按OK。7、按Yes保存更改。使用显示参数值描述标签提供设置参数-该标签标识设备，例如“功率计”。您不能使用显示器编辑此参数。使用离子设置更改设备标签。负载计时器设置PT（A）0-99999指定计时器启动前负载的小平均电流。当读数等于或高于此平均电流阈值时，仪表开始计算工作时间。Pk I dmd for TDD（A）0-99999指定了负载的小峰值电流需求，以包含在总需求失真（TDD）计算中。如果负载电流低于小峰值电流需求阈值，仪表不使用读数计算TDD。如果希望功率计使用计量峰值电流需求进行此计算，请将其设置为“0”（零）。设置区域设置您可以使用本地标准和惯例更改区域设置，以本地化仪表屏幕并以不同语言显示数据。注意：为了显示语言设置参数中列出的语言以外的其他语言，您需要使用固件升级过程将相应的语言文件下载到仪表。1、导航至Maint>Setup。2、输入设置密码（默认为“0”），然后按OK。3、导航至HMI>区域。4、移动光标指向要修改的参数，然后按编辑。5、根据需要修改参数，然后按OK。6、移动光标指向要修改的下一个参数，按Edit，进行更改，然后按OK。7、按向上箭头退出。

Configuring advanced setup parameters using the display You can configure a subset of advanced parameters using the display. 1. Navigate to Maint > Setup. 2. Enter the setup password (default is “0”), then press OK. 3. Navigate to Meter > Advan. 4. Move the cursor to point to the parameter you want to modify, then press Edit. 5. Modify the parameter as required, then press OK. 6. Move the cursor to point to the next parameter you want to modify, press Edit, make your changes, then press OK. 7. Press Yes to save your changes. Advanced setup parameters available using the display Parameter Values Description Label — This label identifies the device, e.g., “Power Meter”. You cannot use the display to edit this parameter. Use ION Setup to change the device label. Load Timer Setpt (A) 0 - 99999 Specifies the minimum average current at the load before the timer starts. The meter begins counting the operating time whenever the readings are equal to or above this average current threshold. Pk I dmd for TDD (A) 0 - 99999 Specifies the minimum peak current demand at the load for inclusion in total demand distortion (TDD) calculations. If the load current is below the minimum peak current demand threshold, the meter does not use the readings to calculate TDD. Set this to “0” (zero) if you want the power meter to use the metered peak current demand for this calculation. Setting up regional settings You can change the regional settings to localize the meter screens and display data in a different language, using local standards and conventions. NOTE: In order to display a different language other than those listed in the Language setup parameter, you need to download the appropriate language file to the meter using the firmware upgrade process. 1. Navigate to Maint > Setup. 2. Enter the setup password (default is “0”), then press OK. 3. Navigate to HMI > Region. 4. Move the cursor to point to the parameter you want to modify, then press Edit. 5. Modify the parameter as required, then press OK. 6. Move the cursor to point to the next parameter you want to modify, press Edit, make your changes, then press OK. 7. Press the up arrow to exit.