VMIVME-4132-010
在所有阶段，必须遵守以下一般安全预防措施
本产品的操作、保养和维修。未能遵守这些
本手册其他地方的预防措施或特定警告违反了安全
本产品的设计、制造和预期用途标准。
GE Fanuc Embedded Systems不对客户未能
遵守这些要求。
系统接地
为将电击危险降至低，机箱和系统机柜必须连接到
电气接地。应使用三芯交流电力电缆。权力
电缆必须插入经批准的三触点电源插座或使用
带三触点到两触点适配器，接地线（绿色）牢固
连接到电源插座处的电气接地（安全接地）。
请勿在爆炸性环境中操作
请勿在存在易燃气体或烟雾的情况下操作系统。的操作
此类环境中的任何电气系统都会构成明确的安全危险。
远离带电电路
操作人员不得拆除产品盖。部件更换和
必须由合格的维护人员进行内部调整。请勿
更换已连接电源线的部件。在某些条件下，
即使拆下电源线，也可能存在危险电压。为了避免受伤，
在接触电源和放电电路之前，务必断开它们。
请勿单独维修或调整
除非另一个人能够
提供急救和复苏。
不要更换零件或修改系统
由于存在引入额外危险的危险，请勿安装替代品
或对产品进行任何未经授权的修改。退回产品
为GE Fanuc嵌入式系统提供服务和维修，以确保安全功能
进行维护。
危险程序警告
警告（如以下示例）仅在潜在危险的程序之前出现
贯穿本手册。必须遵守警告中的说明。
警告：此系统中存在可能导致死亡的危险电压。
搬运、测试和调整时要格外小心

The following general safety precautions must be observed during all phases of the operation, service, and repair of this product. Failure to comply with these precautions or with specific warnings elsewhere in this manual violates safety standards of design, manufacture, and intended use of this product. GE Fanuc Embedded Systems assumes no liability for the customer's failure to comply with these requirements. Ground the System To minimize shock hazard, the chassis and system cabinet must be connected to an electrical ground. A three-conductor AC power cable should be used. The power cable must either be plugged into an approved three-contact electrical outlet or used with a three-contact to two-contact adapter with the grounding wire (green) firmly connected to an electrical ground (safety ground) at the power outlet. Do Not Operate in an Explosive Atmosphere Do not operate the system in the presence of flammable gases or fumes. Operation of any electrical system in such an environment constitutes a definite safety hazard. Keep Away from Live Circuits Operating personnel must not remove product covers. Component replacement and internal adjustments must be made by qualified maintenance personnel. Do not replace components with power cable connected. Under certain conditions, dangerous voltages may exist even with the power cable removed. To avoid injuries, always disconnect power and discharge circuits before touching them. Do Not Service or Adjust Alone Do not attempt internal service or adjustment unless another person, capable of rendering first aid and resuscitation, is present. Do Not Substitute Parts or Modify System Because of the danger of introducing additional hazards, do not install substitute parts or perform any unauthorized modification to the product. Return the product to GE Fanuc Embedded Systems for service and repair to ensure that safety features are maintained. Dangerous Procedure Warnings Warnings, such as the example below, precede only potentially dangerous procedures throughout this manual. Instructions contained in the warnings must be followed. WARNING: Dangerous voltages, capable of causing death, are present in this system. Use extreme caution when handling, testing, and adjusting