TSXAEY1614
PswrdSet将访问密码设置为配置菜单0至1000 Com Addr*将恒温器的Com地址设置为254 PAN ID**将恒温器的PAN ID设置为500通道**将恒温器的通道设置为10至26 Get From**选择恒温器将配置从0导入254 BI1定义二进制输入BI1 None、Rem NSB、Motion NO或NC的使用，窗口BI2定义二进制输入的使用BI2 None、Door Dry、RemOVR、Filter、Service UI3定义通用输入UI3 None、COC/NH、COC/NC、COS、SS MenuScro用于激活或停用菜单滚动打开或关闭自动模式启用模式按钮打开或关闭的自动功能C或F设置温度单位°F，°C%RH显示***使%RH显示在室温以下打开或关闭锁定设置键盘锁定级别0、1、2、3、4、5管道编号定义管道数量并限制允许的顺序2.0管道或4.0管道类型定义主输出开/关的功能或三态浮动顺序Opera定义恒温器0、1、2、3、4的操作顺序，5风扇菜单定义风扇操作的顺序0、1、2、3、4除湿***启用或禁用除湿打开，关闭%RH设置***除湿设定值30至95%除湿***定义湿度控制滞后2至20%除湿***大冷却阀位置当除湿由TM启用20至100%St时，设置备用计时器值0.5至24小时（以0.5小时为增量）Unoc TM设置未占用计时器值0.0至24小时（以0.5小时为增量）St由HT设置备用加热设定值40至90°F（4.5至32.0°C）St By CL将备用冷却设定点54设置为100°F（12.0至37.5°C）Unocc HT将未占用加热设定点40设置为90°F（4.5至32.0°C）Unocc CL将未占用冷却设定点54设置为100°F（12.0至37.5°C）heat max将大加热设定点限制40设置为90°F（4.5至32.0°C）cool min设置小冷却设定点限制54至100°F（12.0至37.5°C）Pb，并将PI控制回路2使用的比例带调整至10°F（0.6至5.6°C）设定类型启用临时设定点功能，Temporar SptFunc为用户双Stp或ATTCHTP设置本地设定点界面。当覆盖0到24小时（以1小时为增量）时，设置临时占用时间。如果门保持打开超过：1到10分钟（以1分钟为增量），门时间强制未占用模式。死区定义小死区2、3、4，5°F cal RS房间空气温度传感器校准±5.0°F cal RH房间相对湿度传感器校准±15.0%aux cont设置辅助触点功能和配置0（再热）；1、2、3、4（占用）；5（网络）自动风扇自动速度风扇模式操作用于风扇序列2和3 AS或AS AD FL时间设置浮动执行器的冲程时间0.5至9分钟（以0.5分钟为增量）cph设置开/关输出3、4、5、6、7的每小时循环数，8再热设置再热输出的时基，如果使用0（4 CPH）或1（PWM 10秒），当UI3配置为模拟输入（SS或COS）时，UI3 dis显示供应或切换温度*仅适用于无线（VT73xxX5000W）和BACnet（VT73xxX5000B）型号**仅适用于无线（VT73xxX5000W）型号***仅适用于带有RH传感器（VT7350C5000X、VT7355C5000X）的型号2个开/关输出2个开/关或浮动输出DEHUM湿度传感器。辅助设备。输出应用程序（中键选项）VT7300A5000● ● 商用VT7305A5000● ● 酒店/住宿VT7300C5000● ● 商用VT7350C5000● ● ● 商用VT7305C5000● ● 酒店/住宿VT7355C5000● ● ● 酒店/住宿T


PswrdSet Sets access password to the configuration menu 0 to 1000 Com Addr* Sets the Com address of the thermostat 0 to 254 PAN ID** Sets the PAN ID of the thermostat 0 to 500 Channel** Sets the channel of the thermostat 10 to 26 Get From** Chooses thermostat to import configuration from 0 to 254 BI1 Defines the use of binary input BI1 None, Rem NSB, Motion NO or NC, Window BI2 Defines the use of binary input BI2 None, Door Dry, RemOVR, Filter, Service UI3 Defines the use of universal input UI3 None, COC/NH, COC/NC, COS, SS MenuScro Used to activate or deactivate menu scroll ON or OFF AutoMode Enables auto function for the mode button ON or OFF C or F Sets temperature units °F, °C %RH disp*** Enables %RH to be displayed below room temperature ON or OFF Lockout Sets the keypad lockout level 0, 1, 2, 3, 4, 5 Pipe No Defines number of pipes and limits sequences allowed 2.0 pipe or 4.0 pipe CntrlTyp Defines functioning of main outputs ON/OFF or Tri-State Floating SeqOpera Defines the sequence of operation of thermostat 0, 1, 2, 3, 4, 5 Fan Menu Defines sequence of fan operation 0, 1, 2, 3, 4 DEHumiLCK*** Enables or disables dehumidification ON, OFF %RH set*** Dehumidification setpoint 30 to 95% DehuHyst*** Defines humidity control hysterisys 2 to 20% DehuCool*** Maximum cooling valve position when dehumidification is enabled 20 to 100% St-By TM Sets the stand-by Timer value 0.5 to 24 hours (in 0.5hr increments) Unocc TM Sets the unoccupied Timer value 0.0 to 24 hours (in 0.5hr increments) St-By HT Sets the stand-by heating setpoint 40 to 90 °F ( 4.5 to 32.0 °C ) St-By CL Sets the stand-by cooling setpoint 54 to 100 °F ( 12.0 to 37.5 °C ) Unocc HT Sets the unoccupied heating setpoint 40 to 90 °F ( 4.5 to 32.0 °C ) Unocc CL Sets the unoccupied cooling setpoint 54 to 100 °F ( 12.0 to 37.5 °C ) heat max Sets the maximum heating setpoint limit 40 to 90 °F ( 4.5 to 32.0 °C ) cool min Sets the minimum cooling setpoint limit 54 to 100 °F ( 12.0 to 37.5 °C ) Pband Adjust the proportional band used by the PI control loop 2 to 10 °F ( 0.6 to 5.6 °C ) Set Type Enables temporary setpoints feature Permnent, Temporar SptFunc Sets the local setpoint interface for the user Dual Stp or AttchStp TOccTime Sets the temporary occupancy time when overriding 0 to 24 hours (in 1 hour increments) DoorTime Forces Unoccupied mode if door stays open more than: 1 to 10 minutes (in 1 minute increments) deadband Defines the minimum deadband 2, 3, 4, 5 °F cal RS Room air temperature sensor calibration ± 5.0 °F cal RH Room relative humidity sensor calibration ± 15.0 % aux cont Sets Auxiliary contact function and configuration 0 (reheat); 1, 2, 3, 4 (occupancy); 5 (network) Auto Fan Auto Speed Fan Mode operation for Fan Sequences 2 and 3 AS or AS AD FL time Sets stroke time of floating actuator 0.5 to 9 minutes (in 0.5 minute increments) cph Sets the number of cycles per hour for On/Off outputs 3, 4, 5, 6, 7, 8 Reheat Sets the time base for the reheat output if used 0 (4 CPH) or 1 (PWM 10 seconds) UI3 dis Displays supply or changeover temperature when UI3 is configured as analog input (SS or COS) * Only available in Wireless (VT73xxX5000W) and BACnet (VT73xxX5000B) models ** Only available in Wireless (VT73xxX5000W) models *** Only available in models with RH Sensor (VT7350C5000X, VT7355C5000X) MODEL 2 ON/OFF OUTPUTS 2 ON/OFF or FLOATING OUTPUTS HUMIDITY SENSOR FOR DEHUM. AUX. OUTPUT APPLICATION (CENTER KEY OPTION) VT7300A5000 ● ● Commercial VT7305A5000 ● ● Hotels/Lodging VT7300C5000 ● ● Commercial VT7350C5000 ● ● ● Commercial VT7305C5000 ● ● Hotels/Lodging VT7355C5000 ● ● ● Hotels/Lodging T